;	For Version 3.59
;
;
;	CONFIGURATION FILE FOR G8BPQ SWITCH SOFTWARE
;
;	The program which converts this text file to binary
;	form is currently very crude - be VERY careful when
;	editing this file!
;
;
;	The order of parameters in not important, but they
;	all must be specified - there are no defaults
;
;
;
;	Memory Usage. If EMS=1, the system will attempt to put its
;	data area into EMS Memory. At the moment it makes no attempt
;	to manage sharing of the EMS window, so you must not run any other
;	software using EMS.
;
;	It seems to work ok when used with Desqview, at least on my
;	AST, but it is primarily intended for use with AA4RE BBS, which
;	needs a great deal of space.
;
;
EMS=0				; dont use EMS RAM
;
;	I seem to have problems with systems not using DESQVIEW - especially
;	NNA BBS's. The DV calls SHOULD be ignored if DV is not loaded, but
;	just in case, if you set DESQVIEW=0, the 'Release Timeslice' call
;	wont be used. MAKE SURE that you set DESQVIEW=1 if using DV, or
;	performance will be seriously affected.
;
DESQVIEW=1
;
;
;	Station Identification.
;
;	If a user connects to the NODE Callsign or Alias, he is linked
;	to the switch code, and can use normal NetRom/TheNet commands
;
;	If he connects to the BBS Callsign or Alias he will be connected
;	directly to a BBS port. If none are available, the connect will
;	be rejected.
;
;	Note that of you are running only a NODE (ie BBS=0), or
;	or just a BBS (NODE=0), then you must still put in two pairs of calls,
;	but they MUST be the SAME.
;
;	If you are running both, the calls MUST be different

NODECALL=G7JJF-8		; NODE CALLSIGN
NODEALIAS=IP0423


BBSCALL=G7JJF		 	; BBS CALLSIGN
BBSALIAS=JJFPMS			; BBS ALIAS

;
;	'ID' MESSAGE - SENT EVERY IDINTERVAL MINS
;
;	WILL BE ADDRESSED FROM THE PORT CALLSIGN (IF DEFINED)
;	     ELSE FROM THE NODE CALL
;
;	The following format allows KA nodes to include your system in
;	their 'Nodes' lists.
;
IDMSG:
Network node (IP0423) running TNCBPQ V1.40 and BPQ Yapp Server V1.00
***
;
UNPROTO=MAIL                         ; DEFAULT UNPROTO ADDR

;	'I' COMMAND TEXT
;
;	Note that the bit about needing a port param in connects is only
;	necessary if you are running more that one (radio) port.
;
INFOMSG:
G7JJF Packet Switch, Sutton In Ashfield, Notts. IO93IC
Commands are basically the same as NET/ROM, but to connect to another
normal station (not another node), you must specify a port number before
the callsign. Use PORTS command to list available ports. The PMS command
connects you to the associated Mailbox and the YAPP command takes you to
a Yapp File Server for downloading/uploading of files.
***
;
;	CTEXT - If specified, will be sent when someone connects to
;	the NODE ALIAS at level 2. It is not sent on connects to the
;	NODE callsign, as this could confuse BBS forwarding connect
;	scripts.
;
CTEXT:
Welcome to G7JJF's Packet Switch in Sutton In Ashfield
Type ? for list of available commands.
***


;	Network System Parameters
;
OBSINIT=5			; INITIAL OBSOLESCENCE VALUE
OBSMIN=4			; MINIMUM TO BROADCAST
NODESINTERVAL=60		; 'NODES' INTERVAL IN MINS
IDINTERVAL=15			; 'ID' BROADCAST INTERVAL (UK Regs require
				; an AX25 ID every 15 mins)
;
BTINTERVAL=15			; NO BEACONS

L3TIMETOLIVE=25			; MAX L3 HOPS
L4RETRIES=3			; LEVEL 4 RETRY COUNT
;
;	I have seen suggestions that L4TIMEOUT should be increased to very
;	high values (even as long as seven mins). Although 60 may be a bit
; 	short in some cases, I STRONGLY advise that you dont go much above
;	120 secs unless you understand ALL the implications.
;
;	I've set TTL and TIMEOUT to the values agreed by the latest SYSOPS
;	meeting - this does not imply that I agree with them!
;
L4TIMEOUT=120			; LEVEL 4 TIMEOUT
L4DELAY=10			; LEVEL 4 DELAYED ACK TIMER
L4WINDOW=4			; DEFAULT LEVEL 4 WINDOW
;
MAXLINKS=30			; MAX LEVEL 2 LINKS (UP,DOWN AND INTERNODE)
MAXNODES=120			; MAX NODES IN SYSTEM
MAXROUTES=35			; MAX ADJACENT NODES
MAXCIRCUITS=64			; NUMBER OF L4 CIRCUITS
minqual=10			; MINIMUM QUALITY TO ADD TO NODES TABLE	
	
BBSQUAL=250			; BBS Quality relative to NODE - used to
				; limit 'spread' of BBS through the network
				; to your required service area. I've been
				; asked to set a low default to encourage you
				; to think about a suitable value. Max is 255

BUFFERS=255			; PACKET BUFFERS - 255 MEANS ALLOCATE AS MANY
				; AS POSSIBLE - NORMALLY ABOUT 130, DEPENDING
				; ON OTHER TABLE SIZES
;
;	TNC DEFAULT PARAMS
;
PACLEN=128			; MAX PACKET SIZE
;
;	PACLEN is a problem! The ideal size depends on the link(s) over
;	which a packet will be sent. For a session involving another node,
;	we have no idea what is at the far end. Ideally each node should have
;	the capability to combine and then refragment messages to suit each
;	link segment - maybe when there are more of my nodes about than 'real'
;	ones, i'll do it. When the node is accessed directly, things are a
;	bit easier, as we know at least something about the link. So, from
;	Version 3.11 onwards, there are two PACLEN params, one here and
;	one in the PORTS section. This one is used to set the initial value
;	for sessions via other nodes, and for sessions initiated from here.
;	The other is used for incoming direct (Level 2)	sessions. In all cases
;	the TNC PACLEN command can be used to override the defaults.
;
;	The main reason for changing this now was a request from someone
;	wanting to run an HF port.
;
;
;
TRANSDELAY=1			; TRANSPARENT MODE SEND DELAY - 1 SEC
;
;	Level 2 Parameters
;
; T1, T2 and N2 are now int the PORTS section
;
T3=180				; LINK VALIDATION TIMER (3 MINS)

IDLETIME=900  			; IDLE LINK SHUTDOWN TIMER (15 MINS)	
;
;
;	Configuration Options
;
BBS=1				; INCLUDE BBS SUPPORT
NODE=1				; INCLUDE SWITCH SUPPORT
;
HIDENODES=0			; IF SET TO 1, NODES STARTING WITH # WILL
				; ONLY BE DISPLAYED BY A NODES * COMMAND
;
;
;
;	'COMBIOS' Port definitions.
;
;	This section defines the virtual TNC's that the code supports.
;
;	I'm afraid this is now rather more complicated than it was!
;
;	You can now define any COMBIOS port to run in normal (TNC2)
;	mode, PK232 HOSTMODE (with varients for UFQ and AA4RE), or KISS
;	mode. KISS mode allows you to run things like TCP/IP, STATS
;	packages, PACSAT Telemetry decode, etc above the switch.
;
;	The basic format is:
;
;	    TNCPORT
;		COM=n		; COMBIOS port number
;		TYPE=TNC2|KISS|PK232/AA4RE|PK232/UFQ
;	        KISSMASK=nn	; Required only for KISS
;		APPLMASK=nn	; Defaults to 1 (BBS)
;	    ENDPORT
;
;	TYPE defaults to TNC2. See file KISSMODE.DOC for full details
;	of facilities available in KISS mode.
;
;	The two PK232 modes are equvalent to the old HOSTMODE=1 or 2,
;	but can now be used on any port. See HOSTMODE.DOC for more details
;
; 	Dont try to define more than 16 ports.
;

TNCPORT
      	COM=1
        TYPE=TNC2
        APPLMASK=$03
        APPLFLAGS=$07
ENDPORT

TNCPORT
      	COM=2
        TYPE=TNC2
        APPLMASK=$08
        APPLFLAGS=$00
ENDPORT

TNCPORT
      	COM=3
        TYPE=TNC2
        APPLMASK=$10
        APPLFLAGS=$00
ENDPORT

TNCPORT
      	COM=4
        TYPE=TNC2
        APPLMASK=$00
        APPLFLAGS=$07
ENDPORT

TNCPORT
      	COM=5
        TYPE=TNC2
        APPLMASK=$08
        APPLFLAGS=$00
ENDPORT

PORT
;	ID=144.625 Mhz 1200 baud
	ID=Not Active
	TYPE=ASYNC
	PROTOCOL=KISS
	IOADDR=2F8H			; COM1 - FOR COM2 PUT 2F8H
	INTLEVEL=3			; COM1 - FOR COM2 PUT 3
	SPEED=9600
	CHANNEL=A
	QUALITY=10
	MAXFRAME=2
	TXDELAY=500
	SLOTTIME=100
	PERSIST=64
	FULLDUP=0
	FRACK=7000
	RESPTIME=2000
	RETRIES=10
	PACLEN=120

ENDPORT
;
;	2ND PORT OF KPC4/KAM (FIRST PORT IS DEFINED AS ABOVE)
;
PORT
;	ID=432.675 Mhz 1200 baud
	ID=144.625 Mhz 1200 baud
	TYPE=ASYNC
	PROTOCOL=KISS
	IOADDR=2F8H
	INTLEVEL=3
	SPEED=9600
	CHANNEL=B			; this is the special bit for KAM/KPC4
	QUALITY=10
	MAXFRAME=2
	TXDELAY=500
	SLOTTIME=100
	PERSIST=64
	FULLDUP=0
	FRACK=7000
	RESPTIME=2000
	RETRIES=10
	PACLEN=120

ENDPORT

ROUTES:
;
;	ROUTES TO LOCK IN
;
;	specify Callsign, Quality and Port. You can now also specify
;	MAXFRAME, FRACK, PACLEN (in that order) to override the port
;	defaults.
;
;
***
;
;	APPLICATIONS SUPPORTED
;
;	UP TO 8 ENTRIES OF UP TO 12 BYTES EACH
;
;	THE FIRST 3 ARE RESERVED FOR BBS, HOST, AND REMOTE SYSOP - YOU
;	CAN DEFINE THE OTHERS AS YOU LIKE.
;
;	FOR COMPATIBILITY WITH EARLIER VERSIONS, JUST ENTER APPLICATIONS=BBS
;
;	NAMES STARTING WITH * ARE NOT INCLUDED IN 'VALID COMMANDS' DISPALY
;
APPLICATIONS=PMS,,*SYS,MH,YAPP
;
;
